PowLu / Debug 启动日志

DDR d5483af87d cym 23/11/23-16:15:24,fwver: v1.15 LPDDR4X, 1800MHz channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB Manufacturer ID:0x13 CH0 RX Vref:28.9%, TX Vref:21.8%,0.0% CH1 RX Vref:29.7%, TX Vref:19.8%,0.0% CH2 RX Vref:28.9%, TX Vref:21.8%,0.0% CH3 RX Vref:28.5%, TX Vref:20.8%,0.0% change to F1: 528MHz change to F2: 1068MHz change to F3: 1560MHz change to F0: 1800MHz out U-Boot SPL board init U-Boot SPL 2017.09-ge4e124926e-230922 #lxh (Sep 25 2023 - 10:58:38), fwver: v1.13 unknown raw ID 0 0 0 unrecognized JEDEC id bytes: 00, 00, 00 Trying to boot from MMC2 SPL: A/B-slot: _a, successful: 0, tries-remain: 7 Trying fit image at 0x4000 sector ## Verified-boot: 0 ## Checking atf-1 0x00040000 ... sha256(64122e141b...) + OK ## Checking uboot 0x00200000 ... sha256(56817984df...) + OK ## Checking fdt 0x00341b18 ... sha256(8ecccd16d2...) + OK ## Checking atf-2 0xff100000 ... sha256(ce8968e34f...) + OK ## Checking atf-3 0x000f0000 ... sha256(ce48b69fdd...) + OK ## Checking optee 0x08400000 ... sha256(b866e4e4a1...) + OK Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000) Total: 499.54/696.715 ms INFO: Preloader serial: 2 NOTICE: BL31: v2.3():v2.3-765-g588059758:derrick.huang, fwver: v1.46 NOTICE: BL31: Built : 18:13:16, Apr 29 2024 INFO: spec: 0x1 INFO: code: 0x88 INFO: ext 32k is not valid INFO: ddr: stride-en 4CH INFO: GICv3 without legacy support detected. INFO: ARM GICv3 driver initialized in EL3 INFO: valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0 INFO: l3 cache partition cfg-0 INFO: system boots from cpu-hwid-0 INFO: disable memory repair INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001 INFO: dfs DDR fsp_params[0].freq_mhz= 1800MHz INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz INFO: BL31: Initialising Exception Handling Framework INFO: BL31: Initializing runtime services INFO: BL31: Initializing BL32 I/TC: I/TC: OP-TEE version: 3.13.0-791-g185dc3c92 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Tue Apr 16 11:16:18 CST 2024 aarch64, fwver: v1.16 I/TC: OP-TEE memory: TEEOS 0x200000 TA 0xc00000 SHM 0x200000 I/TC: Primary CPU initializing I/TC: Primary CPU switching to normal world boot INFO: BL31: Preparing for EL3 exit to normal world INFO: Entry point address = 0x200000 INFO: SPSR = 0x3c9 U-Boot 2017.09-g0a4dd03 #dengtao (Jul 08 2024 - 17:49:16 +0800) Model: Rockchip RK3588 Evaluation Board MPIDR: 0x81000000 PreSerial: 2, raw, 0xfeb50000 DRAM: 4 GiB Sysmem: init Relocation Offset: eda1c000 Relocation fdt: eb9fa7e0 - eb9fecc8 CR: M/C/I Using default environment optee api revision: 2.0 no mmc device at slot 1 mmc@fe2c0000: 1 (SD), mmc@fe2e0000: 0 Bootdev(atags): mmc 1 MMC1: Legacy, 52Mhz PartType: EFI TEEC: Waring: Could not find security partition DM: v2 boot mode: None RESC: 'boot', blk@0x00019462 resource: sha256+ FIT: no signed, no conf required - dev=saradc, channel=7, dtb_adc=2748, read=3010, found=0 - dev=saradc, channel=7, dtb_adc=1410, read=3010, found=0 - dev=saradc, channel=7, dtb_adc=0, read=3010, found=0 DTB: rk-kernel.dtb HASH(c): OK I2c0 speed: 100000Hz vsel-gpios- not found! en-gpios- not found! vdd_cpu_big0_s0 800000 uV vsel-gpios- not found! en-gpios- not found! vdd_cpu_big1_s0 800000 uV I2c1 speed: 100000Hz vsel-gpios- not found! en-gpios- not found! vdd_npu_s0 800000 uV spi2: RK806: 2 ON=0x40, OFF=0x00 vdd_gpu_s0 750000 uV vdd_cpu_lit_s0 750000 uV vdd_log_s0 750000 uV vdd_vdenc_s0 init 750000 uV vdd_ddr_s0 850000 uV Device 'gpio@fd8a0000': seq 0 is in use by 'gpio@fd8a0000' get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts Could not find baseparameter partition Model: ATK-DLRK3588 Board MPIDR: 0x81000000 Rockchip UBOOT DRM driver version: v1.0.1 vp0 have layer nr:2[0 2 ], primary plane: 2 vp1 have layer nr:2[1 3 ], primary plane: 3 vp2 have layer nr:2[6 8 ], primary plane: 8 vp3 have layer nr:2[7 9 ], primary plane: 9 i2c read err! i2c read err! i2c read err! i2c read err! i2c read err! can't get edid block:0 failed to get edid Could not find baseparameter partition color_format:0 hdmi_select_link_config use tmds mode mode:1920x1080 bus_format:0x100a hdmi@fde80000: detailed mode clock 148500 kHz, flags[5] H: 1920 2008 2052 2200 V: 1080 1084 1089 1125 bus_format: 100a VOP update mode to: 1920x1080p60, type: HDMI0 for VP0 dclk:148500,if_pixclk_div;2,if_dclk_div:4 VP0 set crtc_clock to 148500KHz VOP VP0 enable Esmart0[654x270->654x270@633x405] fmt[2] addr[0xedf2c000] CEA mode used vic=16 mtmdsclock:148500000 hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000 hdptx phy pll locked! dw_hdmi_setup HDMI mode don't use dsc mode dw hdmi qp use tmds mode bus_width:0x16a8c8,bit_rate:1485000 hdptx phy lane locked! edid base block is 0, get edid failed can't get edid block:0 failed to get edid Could not find baseparameter partition color_format:0 hdmi_select_link_config use tmds mode mode:1920x1080 bus_format:0x100a hdmi@fdea0000: detailed mode clock 148500 kHz, flags[5] H: 1920 2008 2052 2200 V: 1080 1084 1089 1125 bus_format: 100a VOP update mode to: 1920x1080p60, type: HDMI1 for VP1 dclk:148500,if_pixclk_div;2,if_dclk_div:4 VP1 set crtc_clock to 148500KHz VOP VP1 enable Esmart1[654x270->654x270@633x405] fmt[2] addr[0xedf2c000] CEA mode used vic=16 mtmdsclock:148500000 hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000 hdptx phy pll locked! dw_hdmi_setup HDMI mode don't use dsc mode dw hdmi qp use tmds mode bus_width:0x16a8c8,bit_rate:1485000 hdptx phy lane locked! CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A) b0pll 24000 KHz b1pll 24000 KHz lpll 24000 KHz v0pll 24000 KHz aupll 786431 KHz cpll 1500000 KHz gpll 1188000 KHz npll 850000 KHz ppll 1100000 KHz aclk_center_root 702000 KHz pclk_center_root 100000 KHz hclk_center_root 396000 KHz aclk_center_low_root 500000 KHz aclk_top_root 750000 KHz pclk_top_root 100000 KHz aclk_low_top_root 396000 KHz Net: eth1: ethernet@fe1c0000, eth0: ethernet@fe1b0000 Hit key to stop autoboot('CTRL+C'): 0 ANDROID: reboot reason: "(none)" Not AVB images, AVB skip No valid android hdr Android image load failed Android boot failed, error -1. ## Booting FIT Image at 0xe956d3c0 with size 0x0228c400 Fdt Ramdisk skip relocation ## Loading kernel from FIT Image at e956d3c0 ... Using 'conf' configuration ## Verified-boot: 0 Trying 'kernel' kernel subimage Description: unavailable Type: Kernel Image Compression: uncompressed Data Start: 0xe95b3dc0 Data Size: 35936768 Bytes = 34.3 MiB Architecture: AArch64 OS: Linux Load Address: 0x00400000 Entry Point: 0x00400000 Hash algo: sha256 Hash value: a815dc0908ab24e94c4090af9ca674fe654c69f3b240fddce32a9e99aca222a7 Verifying Hash Integrity ... sha256 Bad hash: 23ba0d82a15a368c517ab31799338a6510af80b74508fcaa4529cef7429f1d24 error! Bad hash value for 'hash' hash node in 'kernel' image node Bad Data Hash ERROR: can't get kernel image! Unknown command 'bootrkp' - try 'help' switch to partitions #0, OK mmc1 is current device Failed to mount ext2 filesystem... ** Unrecognized filesystem type ** switch to partitions #0, OK mmc0(part 0) is current device Failed to mount ext2 filesystem... ** Unrecognized filesystem type ** Device 2: unrecognized JEDEC id bytes: 00, 00, 00 unknown device Device 1: unknown raw ID 0 0 0 Device 0: unknown device starting USB... Bus usb@fc000000: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 Bus usb@fc800000: USB EHCI 1.00 Bus usb@fc840000: USB OHCI 1.0 Bus usb@fc880000: USB EHCI 1.00 Bus usb@fc8c0000: USB OHCI 1.0 Bus usb@fcd00000: usb maximum-speed not found Failed to get USB PHY0 for usb@fcd00000 Port not available. Bus usb@fc400000: usb maximum-speed not found Register 2000140 NbrPorts 2 Starting the controller USB XHCI 1.10 scanning bus usb@fc000000 for devices... 1 USB Device(s) found scanning bus usb@fc800000 for devices... WARN: interface 0 has 2 endpoint descriptor, different from the interface descriptor's value: 1 2 USB Device(s) found scanning bus usb@fc840000 for devices... 1 USB Device(s) found scanning bus usb@fc880000 for devices... 1 USB Device(s) found scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found scanning bus usb@fc400000 for devices... 1 USB Device(s) found scanning usb for storage devices... 0 Storage Device(s) found Device 0: unknown device EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: pxeuuid missing environment variable: bootfile Retrieving file: pxelinux.cfg/01-c2-a4-c0-68-1f-d9 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000000 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000000 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/000000 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/00000 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/0000 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/000 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/00 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/0 EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm-rockchip EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/default-arm EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile Retrieving file: pxelinux.cfg/default EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11Config file not found EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11=>