いいね 0
フォーク 0

最終更新 1781069932

PowLu revised this gist 1781069932. Go to revision

No changes

PowLu revised this gist 1781069914. Go to revision

1 file changed, 291 insertions

启动日志.log(file created)

@@ -0,0 +1,291 @@
1 + DDR d5483af87d cym 23/11/23-16:15:24,fwver: v1.15
2 + LPDDR4X, 1800MHz
3 + channel[0] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
4 + channel[1] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
5 + channel[2] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
6 + channel[3] BW=16 Col=10 Bk=8 CS0 Row=16 CS=1 Die BW=16 Size=1024MB
7 + Manufacturer ID:0x13
8 + CH0 RX Vref:28.9%, TX Vref:21.8%,0.0%
9 + CH1 RX Vref:29.7%, TX Vref:19.8%,0.0%
10 + CH2 RX Vref:28.9%, TX Vref:21.8%,0.0%
11 + CH3 RX Vref:28.5%, TX Vref:20.8%,0.0%
12 + change to F1: 528MHz
13 + change to F2: 1068MHz
14 + change to F3: 1560MHz
15 + change to F0: 1800MHz
16 + out
17 + U-Boot SPL board init
18 + U-Boot SPL 2017.09-ge4e124926e-230922 #lxh (Sep 25 2023 - 10:58:38), fwver: v1.13
19 + unknown raw ID 0 0 0
20 + unrecognized JEDEC id bytes: 00, 00, 00
21 + Trying to boot from MMC2
22 + SPL: A/B-slot: _a, successful: 0, tries-remain: 7
23 + Trying fit image at 0x4000 sector
24 + ## Verified-boot: 0
25 + ## Checking atf-1 0x00040000 ... sha256(64122e141b...) + OK
26 + ## Checking uboot 0x00200000 ... sha256(56817984df...) + OK
27 + ## Checking fdt 0x00341b18 ... sha256(8ecccd16d2...) + OK
28 + ## Checking atf-2 0xff100000 ... sha256(ce8968e34f...) + OK
29 + ## Checking atf-3 0x000f0000 ... sha256(ce48b69fdd...) + OK
30 + ## Checking optee 0x08400000 ... sha256(b866e4e4a1...) + OK
31 + Jumping to U-Boot(0x00200000) via ARM Trusted Firmware(0x00040000)
32 + Total: 499.54/696.715 ms
33 +
34 + INFO: Preloader serial: 2
35 + NOTICE: BL31: v2.3():v2.3-765-g588059758:derrick.huang, fwver: v1.46
36 + NOTICE: BL31: Built : 18:13:16, Apr 29 2024
37 + INFO: spec: 0x1
38 + INFO: code: 0x88
39 + INFO: ext 32k is not valid
40 + INFO: ddr: stride-en 4CH
41 + INFO: GICv3 without legacy support detected.
42 + INFO: ARM GICv3 driver initialized in EL3
43 + INFO: valid_cpu_msk=0xff bcore0_rst = 0x0, bcore1_rst = 0x0
44 + INFO: l3 cache partition cfg-0
45 + INFO: system boots from cpu-hwid-0
46 + INFO: disable memory repair
47 + INFO: idle_st=0x21fff, pd_st=0x11fff9, repair_st=0xfff70001
48 + INFO: dfs DDR fsp_params[0].freq_mhz= 1800MHz
49 + INFO: dfs DDR fsp_params[1].freq_mhz= 528MHz
50 + INFO: dfs DDR fsp_params[2].freq_mhz= 1068MHz
51 + INFO: dfs DDR fsp_params[3].freq_mhz= 1560MHz
52 + INFO: BL31: Initialising Exception Handling Framework
53 + INFO: BL31: Initializing runtime services
54 + INFO: BL31: Initializing BL32
55 + I/TC:
56 + I/TC: OP-TEE version: 3.13.0-791-g185dc3c92 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #2 Tue Apr 16 11:16:18 CST 2024 aarch64, fwver: v1.16
57 + I/TC: OP-TEE memory: TEEOS 0x200000 TA 0xc00000 SHM 0x200000
58 + I/TC: Primary CPU initializing
59 + I/TC: Primary CPU switching to normal world boot
60 + INFO: BL31: Preparing for EL3 exit to normal world
61 + INFO: Entry point address = 0x200000
62 + INFO: SPSR = 0x3c9
63 +
64 +
65 + U-Boot 2017.09-g0a4dd03 #dengtao (Jul 08 2024 - 17:49:16 +0800)
66 +
67 + Model: Rockchip RK3588 Evaluation Board
68 + MPIDR: 0x81000000
69 + PreSerial: 2, raw, 0xfeb50000
70 + DRAM: 4 GiB
71 + Sysmem: init
72 + Relocation Offset: eda1c000
73 + Relocation fdt: eb9fa7e0 - eb9fecc8
74 + CR: M/C/I
75 + Using default environment
76 +
77 + optee api revision: 2.0
78 + no mmc device at slot 1
79 + mmc@fe2c0000: 1 (SD), mmc@fe2e0000: 0
80 + Bootdev(atags): mmc 1
81 + MMC1: Legacy, 52Mhz
82 + PartType: EFI
83 + TEEC: Waring: Could not find security partition
84 + DM: v2
85 + boot mode: None
86 + RESC: 'boot', blk@0x00019462
87 + resource: sha256+
88 + FIT: no signed, no conf required
89 + - dev=saradc, channel=7, dtb_adc=2748, read=3010, found=0
90 + - dev=saradc, channel=7, dtb_adc=1410, read=3010, found=0
91 + - dev=saradc, channel=7, dtb_adc=0, read=3010, found=0
92 + DTB: rk-kernel.dtb
93 + HASH(c): OK
94 + I2c0 speed: 100000Hz
95 + vsel-gpios- not found!
96 + en-gpios- not found!
97 + vdd_cpu_big0_s0 800000 uV
98 + vsel-gpios- not found!
99 + en-gpios- not found!
100 + vdd_cpu_big1_s0 800000 uV
101 + I2c1 speed: 100000Hz
102 + vsel-gpios- not found!
103 + en-gpios- not found!
104 + vdd_npu_s0 800000 uV
105 + spi2: RK806: 2
106 + ON=0x40, OFF=0x00
107 + vdd_gpu_s0 750000 uV
108 + vdd_cpu_lit_s0 750000 uV
109 + vdd_log_s0 750000 uV
110 + vdd_vdenc_s0 init 750000 uV
111 + vdd_ddr_s0 850000 uV
112 + Device 'gpio@fd8a0000': seq 0 is in use by 'gpio@fd8a0000'
113 + get vp0 plane mask:0x5, primary id:2, cursor_plane:-1, from dts
114 + get vp1 plane mask:0xa, primary id:3, cursor_plane:-1, from dts
115 + get vp2 plane mask:0x140, primary id:8, cursor_plane:-1, from dts
116 + get vp3 plane mask:0x280, primary id:9, cursor_plane:-1, from dts
117 + Could not find baseparameter partition
118 + Model: ATK-DLRK3588 Board
119 + MPIDR: 0x81000000
120 + Rockchip UBOOT DRM driver version: v1.0.1
121 + vp0 have layer nr:2[0 2 ], primary plane: 2
122 + vp1 have layer nr:2[1 3 ], primary plane: 3
123 + vp2 have layer nr:2[6 8 ], primary plane: 8
124 + vp3 have layer nr:2[7 9 ], primary plane: 9
125 + i2c read err!
126 + i2c read err!
127 + i2c read err!
128 + i2c read err!
129 + i2c read err!
130 + can't get edid block:0
131 + failed to get edid
132 + Could not find baseparameter partition
133 + color_format:0
134 + hdmi_select_link_config use tmds mode
135 + mode:1920x1080 bus_format:0x100a
136 + hdmi@fde80000: detailed mode clock 148500 kHz, flags[5]
137 + H: 1920 2008 2052 2200
138 + V: 1080 1084 1089 1125
139 + bus_format: 100a
140 + VOP update mode to: 1920x1080p60, type: HDMI0 for VP0
141 + dclk:148500,if_pixclk_div;2,if_dclk_div:4
142 + VP0 set crtc_clock to 148500KHz
143 + VOP VP0 enable Esmart0[654x270->654x270@633x405] fmt[2] addr[0xedf2c000]
144 + CEA mode used vic=16
145 + mtmdsclock:148500000
146 + hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
147 + hdptx phy pll locked!
148 + dw_hdmi_setup HDMI mode
149 + don't use dsc mode
150 + dw hdmi qp use tmds mode
151 + bus_width:0x16a8c8,bit_rate:1485000
152 + hdptx phy lane locked!
153 + edid base block is 0, get edid failed
154 + can't get edid block:0
155 + failed to get edid
156 + Could not find baseparameter partition
157 + color_format:0
158 + hdmi_select_link_config use tmds mode
159 + mode:1920x1080 bus_format:0x100a
160 + hdmi@fdea0000: detailed mode clock 148500 kHz, flags[5]
161 + H: 1920 2008 2052 2200
162 + V: 1080 1084 1089 1125
163 + bus_format: 100a
164 + VOP update mode to: 1920x1080p60, type: HDMI1 for VP1
165 + dclk:148500,if_pixclk_div;2,if_dclk_div:4
166 + VP1 set crtc_clock to 148500KHz
167 + VOP VP1 enable Esmart1[654x270->654x270@633x405] fmt[2] addr[0xedf2c000]
168 + CEA mode used vic=16
169 + mtmdsclock:148500000
170 + hdptx_ropll_cmn_config bus_width:16a8c8 rate:1485000
171 + hdptx phy pll locked!
172 + dw_hdmi_setup HDMI mode
173 + don't use dsc mode
174 + dw hdmi qp use tmds mode
175 + bus_width:0x16a8c8,bit_rate:1485000
176 + hdptx phy lane locked!
177 + CLK: (sync kernel. arm: enter 1008000 KHz, init 1008000 KHz, kernel 0N/A)
178 + b0pll 24000 KHz
179 + b1pll 24000 KHz
180 + lpll 24000 KHz
181 + v0pll 24000 KHz
182 + aupll 786431 KHz
183 + cpll 1500000 KHz
184 + gpll 1188000 KHz
185 + npll 850000 KHz
186 + ppll 1100000 KHz
187 + aclk_center_root 702000 KHz
188 + pclk_center_root 100000 KHz
189 + hclk_center_root 396000 KHz
190 + aclk_center_low_root 500000 KHz
191 + aclk_top_root 750000 KHz
192 + pclk_top_root 100000 KHz
193 + aclk_low_top_root 396000 KHz
194 + Net: eth1: ethernet@fe1c0000, eth0: ethernet@fe1b0000
195 + Hit key to stop autoboot('CTRL+C'): 0
196 + ANDROID: reboot reason: "(none)"
197 + Not AVB images, AVB skip
198 + No valid android hdr
199 + Android image load failed
200 + Android boot failed, error -1.
201 + ## Booting FIT Image at 0xe956d3c0 with size 0x0228c400
202 + Fdt Ramdisk skip relocation
203 + ## Loading kernel from FIT Image at e956d3c0 ...
204 + Using 'conf' configuration
205 + ## Verified-boot: 0
206 + Trying 'kernel' kernel subimage
207 + Description: unavailable
208 + Type: Kernel Image
209 + Compression: uncompressed
210 + Data Start: 0xe95b3dc0
211 + Data Size: 35936768 Bytes = 34.3 MiB
212 + Architecture: AArch64
213 + OS: Linux
214 + Load Address: 0x00400000
215 + Entry Point: 0x00400000
216 + Hash algo: sha256
217 + Hash value: a815dc0908ab24e94c4090af9ca674fe654c69f3b240fddce32a9e99aca222a7
218 + Verifying Hash Integrity ... sha256 Bad hash: 23ba0d82a15a368c517ab31799338a6510af80b74508fcaa4529cef7429f1d24
219 + error!
220 + Bad hash value for 'hash' hash node in 'kernel' image node
221 + Bad Data Hash
222 + ERROR: can't get kernel image!
223 + Unknown command 'bootrkp' - try 'help'
224 + switch to partitions #0, OK
225 + mmc1 is current device
226 + Failed to mount ext2 filesystem...
227 + ** Unrecognized filesystem type **
228 + switch to partitions #0, OK
229 + mmc0(part 0) is current device
230 + Failed to mount ext2 filesystem...
231 + ** Unrecognized filesystem type **
232 +
233 + Device 2: unrecognized JEDEC id bytes: 00, 00, 00
234 + unknown device
235 +
236 + Device 1: unknown raw ID 0 0 0
237 +
238 + Device 0: unknown device
239 + starting USB...
240 + Bus usb@fc000000: usb maximum-speed not found
241 + Register 2000140 NbrPorts 2
242 + Starting the controller
243 + USB XHCI 1.10
244 + Bus usb@fc800000: USB EHCI 1.00
245 + Bus usb@fc840000: USB OHCI 1.0
246 + Bus usb@fc880000: USB EHCI 1.00
247 + Bus usb@fc8c0000: USB OHCI 1.0
248 + Bus usb@fcd00000: usb maximum-speed not found
249 + Failed to get USB PHY0 for usb@fcd00000
250 + Port not available.
251 + Bus usb@fc400000: usb maximum-speed not found
252 + Register 2000140 NbrPorts 2
253 + Starting the controller
254 + USB XHCI 1.10
255 + scanning bus usb@fc000000 for devices... 1 USB Device(s) found
256 + scanning bus usb@fc800000 for devices... WARN: interface 0 has 2 endpoint descriptor, different from the interface descriptor's value: 1
257 + 2 USB Device(s) found
258 + scanning bus usb@fc840000 for devices... 1 USB Device(s) found
259 + scanning bus usb@fc880000 for devices... 1 USB Device(s) found
260 + scanning bus usb@fc8c0000 for devices... 1 USB Device(s) found
261 + scanning bus usb@fc400000 for devices... 1 USB Device(s) found
262 + scanning usb for storage devices... 0 Storage Device(s) found
263 +
264 + Device 0: unknown device
265 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: pxeuuid
266 + missing environment variable: bootfile
267 + Retrieving file: pxelinux.cfg/01-c2-a4-c0-68-1f-d9
268 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
269 + Retrieving file: pxelinux.cfg/00000000
270 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
271 + Retrieving file: pxelinux.cfg/0000000
272 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
273 + Retrieving file: pxelinux.cfg/000000
274 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
275 + Retrieving file: pxelinux.cfg/00000
276 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
277 + Retrieving file: pxelinux.cfg/0000
278 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
279 + Retrieving file: pxelinux.cfg/000
280 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
281 + Retrieving file: pxelinux.cfg/00
282 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
283 + Retrieving file: pxelinux.cfg/0
284 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
285 + Retrieving file: pxelinux.cfg/default-arm-rockchip
286 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
287 + Retrieving file: pxelinux.cfg/default-arm
288 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11missing environment variable: bootfile
289 + Retrieving file: pxelinux.cfg/default
290 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11Config file not found
291 + EQOS_DMA_MODE_SWR stuckFAILED: -11EQOS_DMA_MODE_SWR stuckFAILED: -11=>
Newer Older

Powered by Opengist ⋅ Load: 20ms⋅

日本語